|
密封材料 |
適用溫度
|
應用範圍 |
特性說明 |
是否硬化 |
|
289
*VOC Service
|
|
閥門，法蘭，附件。降低或消除溢散性排放的VOC閥門襯墊。
|
這是非固化性，可高度壓縮的，這化合物是持久的，並將保持半柔性於極高溫度和壓力下。這是非常光滑，低摩擦，閥門襯墊。
|
不會硬化 |
|
389
*VOC Service
|
-34°C至982°C
|
閥門，法蘭，附件。降低或消除溢散性排放的VOC閥門襯墊。 |
這是非固化性，可高度壓縮的，這化合物是持久的，並將保持半柔性於極高溫度和壓力下。這是非常光滑，低摩擦，閥門襯墊。
|
不會硬化 |
|
489
*VOC Service
|
-34°C至482°C
|
閥門，法蘭，附件。降低或消除溢散性排放的VOC閥門襯墊。 |
這是非固化性，這化合物是持久的，並將保持半柔性於極高溫度和壓力下。這是非常光滑，低摩擦，閥門襯墊。
|
不會硬化 |
|
300
|
-117°C至260°C
|
Packing and sealant for claves, falangs and enclosures.
|
Excellant resistance to most sovents and acids.(Not for use on Oxidizing Chemicals)
|
不會硬化 |
|
348
|
-117°C至260°C
|
Packing and sealant for calves, flanges enclosures.
|
Excellent resistance to most solvents and acids. (Not for use on Oxidizing Chemials)
|
不會硬化 |
|
|
|
Packing for valves, flanges and enclosures.
|
Excellent
resistance to most solvents and acids. NOT recommended for Oxygen
service. (refer to Deacon Application Reference Guide)
|
不會硬化 |
|
375
|
-45°C至260°C
|
Valves, Flanges, Enclosures, Etc.
|
This is a non-curing compound with good lubricity and low friction charactoritics.
|
不會硬化 |
|
375-OX
|
-45°C至260°C
|
Valves,Flanges,Enclosures,Etc. |
This is a non-curing compound with good lubricity and low friction characteristics.
|
不會硬化 |
|
375-OXP
|
-45°C至260°C
|
Valves,Flanges,Enclosures,Etc. |
This is a non-curing compound with good lubricity and low friction characteristics. (thinner paste vision)
|
不會硬化 |
|
427
|
至204°C
|
is
a two-part system that cures at room tempersature (18 to 21°C) in
24 hours. heat curing is also an option for a faster set up time and to
further increase temperature resistance. |
427 contains no solvents with aids inthe low shrinkage characteristics .
Ultimate tensile strength is 7500PSI.(liquid mix)
|
Over 4.4°C,(24 hr. cure faster with heat)
|
|
30-L
|
|
|
|
|
|
VP1000
|
-31°C至315°C
|
Valve packing and sealant for valves and enclosures.
|
(non-curing compound) Excellent tavel, good lubricity, good on water, steam, and air leaks.
|
不會硬化
|
|
2018
|
|
|
|
|
|
2121
|
|
|
|
|
|
3100S
|
121°C至510°C
|
Flanges,
valves, enclosures. Excellent sealant / packing for use on hot oil,
hydrocarbons, steam, Dowtherm, various chemical applications. (refer to
Deacon Application Reference Guide)
|
Cures with heat, above 200 deg. F. A positive seal can normally be reached before a full cure.
|
Over 121°C(add accelerator below 242°C)
|
|
3300
|
315°C至871°C
|
Gasket
Replacement
Access
Doors
Flanges (Cut,Warped or Pitted)
|
To
complete the seal, simply cross the two ends. Deacon 3300 should
be pressed firmly into place as to resemble a tape-like seal |
Steam Cut Repair
|
|
|
|
Steam, Boiler Feed Water, Condensate, Plugging Holes, Wire Wraps, High Pressure, Bad blows.
|
Excellent bridging capabilities. Cure time can be accelerated by adding Deacon 19-A Accelerator.
|
Over 121°C(add accelerator below 242°C)
|
